Vibrations in engineering and technology

Paladiychuk Yuriy– Candidate of Science (Engineering), Associate Professor of the Department of Agroengineering and Technical Service of Vinnitsa National Agrarian University (3 Soniachna St., Vinnitsa, 21008, Ukraine, e-mail: rewet@vsau.vin.ua).

Telyatnuk Inna– postgraduate of Vinnytsia National Agrarian University (3, Solnychna st., Vinnytsa)

One of the ways to increase the fatigue strength and wear resistance of parts is defamation of the surface layer of the working surfaces of the parts as a whole and in stress concentration zones. Plastic deformation takes place when the load increases, which is higher than the elastic strength of the material, as the metal strengthens during the deformation process. The bulk of industrial alloys have a polycrystalline structure. During the deformation of polycrystals, there is no sliding stage, the deformation of the grains begins immediately along several sliding systems and is accompanied by bending and twisting of the sliding planes. The total deformation is small and amounts to 1%, the grains are deformed heterogeneously due to their different orientation in relation to the applied loads. As the deformation changes, the difference between the grains of the material decreases and the microstructure changes: the metal grains are gradually pulled out in the direction of the plastic flow, which leads to a change in the grains of the crystal lattice of the metal with an increase in the density of defects.

The reliability of machine parts primarily depends on their strength, wear resistance, vibration resistance, heat resistance, etc. These criteria for the reliability of machine parts are provided by various methods and measures during their manufacture, such as: material selection and various methods of increasing strength and wear resistance - heat treatment, treatment by various physical methods of the surface of the part and areas of stress concentration, etc.

The introduction of modern methods and tools in the development of mechanical engineering ensures an increase in the reliability of parts and products in general, as well as a reduction in the cost of production.

This article analyzes the types and designs of known vibration equipment and vibration exciters used in mechanical engineering. The structural diagram of vibration equipment production is considered.

Determination of the main advantages and disadvantages of vibration equipment and vibration exciters..

1. Iskovich-Lotockij R. D., Ivanchuk Ya. V. Pidvishennya efektivnosti rozvantazhennya materialiv pid diyeyu periodichnih udarnih impulsive. Vibraciyi v tehnici i tehnologiyah. 2008. № 2 (51). S. 8-11. 

2. Goldshtejn M. N., Carkov A. A., Cherkasov I. I. Mehanika gruntov, osnovaniya i fundamenty. Visnik Vinnickogo politehnichnogo institutu. 2022. № 1 S. 110.

3. Iskovich-Lotockij R. D., Ivanchuk Ya. V. Doslidzhennya dinamiki procesu roboti universalnogo gidravlichnogo vibroudranogo privodu dlya rozvantazhennya transportnih zasobiv. Naukovi notatki. Mizhvuzivskij zbirnik (za napryamom «Inzhenerna mehanika»). 2007. № 20. S. 184-187. 

4. Miskov V. P. Inercijnij vibropres-molot z elektrogidravlichnoyu sistemoyu keruvannya gidroimpulsnogo privoda dlya formoutvorennya zagotovok z poroshkovih materialiv : avtoref. dis. na zdobuttya nauk. stupenya kand. tehn. nauk : spec. 05.03.05 / Miskov Vadim Petrovich – Vinnicya, 2015. – 22 s.

5. Iskovych-Lototsky R., Veselovska N. Automatic system for modeling vibro-impact unloading bulk cargo on vehicles. Proc. SPIE 10808, Photonics Applications in Astronomy, Communications, Industry, and High-Energy Physics Experiments 2018. 1080860 (1 October 2018): veb-sajt. URL: https://doi.org/10.1117/12.2501526. (data zvernennya 30.09.2022)

6. Rostislav Iskovych-Lototsky, Yaroslav Ivanchuk, Yaroslav Veselovsky, Konrad Gromaszek, and Ayaulym Oralbekova. Automatic system for modeling of working processes in pressure generators of hydraulic vibrating and vibro-impact machine. Proc. SPIE 10808, Photonics Applications in Astronomy, Communications, Industry, and High-Energy Physics Experiments 2018. 1080850 (1 October 2018): veb-sajt. URL: https://doi.org/ 10.1117/12.2501532. (data zvernennya 30.09.2022).

7. Iskovich-Lotockij R. D., Ivanchuk Ya. V., Veselovskij Ya. P. Osnovi rezonansno-strukturnoyi teoriyi vibroudarnogo rozvantazhennya transportnih zasobiv. Nauka ta progres transportu. Visnik Dnipropetrovskogo nacionalnogo universitetu zaliznichnogo transportu im. akademika V. Lazaryana. 2014. № 5 (53). S. 109-118.

8. S. Matysiak, and P. Pusz. Axisummetric bousinesg problem for a granular hal. Bulletin of Polish Academie of Scienes, Technical Sciences. 1985. 33 (7/8), pp. 351-358.

9. D. I. Zolotarevskaya. Mathematical simulation and calculation of the soil compaction under dynamic loads. Eurasian Soil Science. 2011. № 44 (4), pp. 407-416.

10. A. Li, F. Dai, N. Xu, G. Gu, and Z. Hu. Analysis of a Complex Flexural Toppling Failure of Large Underground Caverns in Layered Rock Masses. Rock Mechanics and Rock Engineering: veb-sajt. URL: https://doi.org/10.1007/s00603-019-01760-5. (data zvernennya 01.10.2022)

11. C. Debeleac, S. Nastac. Stochastic Approaches of Nonlinear Model-Based Simulations for Vibratory Compaction Process. PAMM. 2014. vol. 14 (1), pp. 749-750.