Issue №: 4(99)
The journal deals with the problems of vibration technologies and machines, mathematical methods of vibration process studies, information on design and technological development, presents teaching and methodological aspects of teaching in the Higher School of Applied Sciences, where vibration machines and technologies are studied.
CONTROLLED VIBRATING MILL FOR GRINDING BULK MEDIUM
Solona Olena – Candidate of Technical Sciences (Ph. D in Engeneering), Associate Professor of the Department of General Technical Disciplines and Labor Protection, Vinnytsia National Agrarian University (3, Solnyschaya St., Vinnytsia, Ukraine,21008, e-mail: solona_o_v@ukr.net).
One of the advanced types of grinding equipment are vibrating mills, which provide high specific productivity at relatively low energy consumption, adjustable tone of grinding products.
Vibration impact on the product significantly increases the shock-absorbing effect with the possibility of wide and separate variation of shock and abrasion factors. Significant speed of mechanical and heat and mass transfer processes, a high degree of homogeneity of the obtained products, the possibility of efficient fine grinding and dispersion of the product at relatively low energy consumption lead to the widespread use of vibratory grinding.
The constructive scheme of the mill is developed, in which the flat vertical vibrating field provides lifting of a part of loading and by means of the transport-reloading device carries out its continuous adjustable movement from one grinding chamber to another, thereby circulating-spatial movement of the environment in which there is a grinding process. shock interaction of grinding bodies and material that is crushed.
The priority direction of development of science and technologies at the modern level is the development, creation and implementation of new generation mechatronic systems.
One of the most important rules for the construction of vibrating mills is the need to maximize the degree of their automation in order to increase productivity, improve the quality of grinding and reduce the cost of the process.
Also in the article the structural model of the controlled vibromill with spatial-circulating loading movement which at change of weight of a working body in the course of separation and unloading of the crushed material from a grinding chamber constantly adapt to a resonant mode of work at the set technologically optimum parameters (productivity) and the minimum power consumption.
1. Ovchynnykov P.F.(1968).O kharaktere udarnoho razrushenyia v vybromelnytsakh . Prykladnaia mekhanyka. №4. 104-110.
2. Klymovych V.U. (1962). Эksperymentalnыe yssledovanyia y nekotorыe voprosы realyzatsyy trubnoi vybratsyonnoi melnytsы. Omsk. 80.
3. 3elentsov L.K. (1974). Vlyianye rabochei sredы na kolebanyia vybratsyonnoi ustanovky dlia obъemnoi obrabotky detalei. Sostoianye y perspektyvы promыshlennoho osvoenyia vybratsyonnoi obrabotky. Rostov-na-Donu. 37-41.
4. Poturaev V.N., Franchuk V.P.(1970). Nekotorыe teoretycheskye predposыlky k yssledovanyiu mekhanyky dvyzhenyia bolshoho sloia nasыpnoho hruza pod deistvyem vybratsyy. K.: Naukova dumka. 173-181.
5. Vainkof Ya.F., Kvytko A.K.(1964). Vybratsyonnaia tekhnyka na vspomohatelnыkh transportnыkh operatsyiakh. M.: Mashynostroenye. 124.
6. Rose H.E.(1962). Hochleistungs-Schwingmuhlen. Chemie-Jngr-Tech. 34. Janrg.6.
7. Raasch J.(1962). Zuz Mechanik der Schwingmuhlen - Chemie-Jngr-Tech. 2.
8. Poturaev V.N., Franchuk V.P., Kukhar A.H., Zubov L.N.(1975).Trudы VNYYPY mekh. obrabotky poleznыkh yskopaemыkh. Vыp. 140. (91-95).
9. Chubyk R. V. (2007). Adaptyvna systema keruvannia rezhymamy rezonansnykh vibratsiinykh tekhnolohichnykh mashyn Dys. k-ta tekhn. nauk. Lviv. 266 .
10. Pat. 87776 A Ukraina, B65G27/00. Sposib keruvannia robotoiu adaptyvnykh vibratsiinykh tekhnolohichnykh mashyn. Sereda L.P., Chubyk R.V. Yaroshenko L.V. (Ukraina). № a200803685. Opubl. 10.08.2009. Biul. № 15, 4 st.
11. Chubyk R.V., Yaroshenko L.V.( 2008). Metod stabilizatsii tekhnolohichno optymalnykh parametriv vibratsiinoho polia adaptyvnykh vibratsiinykh tekhnolohichnykh mashyn . Vibratsii v tekhnitsi ta tekhnolohiiakh. № 2(51). 57-60.
12. Solona O.V.(2006.) Obgruntuvannia parametriv vibratsiinoho mlyna z prostorovo-tsyrkuliatsiinym rukhom hirskoi masy Dys... k-ta tekhn. nauk. Dnipropetrovsk. 174 .
13. Pat. 43792 A Ukraina. B 02C19/16. Vibratsiinyi mlyn. P.C. Bernyk, P.D. Denisov, O.V. Solona. (Ukraina) №98126996. Zaiavl. 29.12.98.Opub. 17.12.2001. Biul.№11 .3.
14. Povidailo V. O. (2004).Vibratsiini protsesy ta obladnannia. Lviv. Vydavnytstvo NU "Lvivska politekhnika". 248 .
15. Tymoshenko S. P., Yanh D. Zh., Uyver U. (1985). (Perevod s anhlyiskoho kand. fyz.mat. nauk Korneichuka L. H. pod red. chl.korr. AN SSR Hryholiuka Э. Y.) Kolebanyia v ynzhenernom dele. M.: Mashynostroenye. 472 .
16. Khaikyn S.Э.( 1971). Fyzycheskye osnovы mekhanyky. M.: Nauka. 751 .
17. Serheev A.P.( 1966). Yssledovanye protsessa obrabotky, mekhanyzatsyia y avtomatyzatsyia vspomohatelnыkh rabot na mashynakh dlia obъemnoi vybratsyonnoi obrabotky . Mekhanyzatsyia protsessa sniatyia zausentsev. MDNTP. M.74-85.
18. Serdiuk L.Y., Davыdenko Yu.A., Osyna L.M.(1966). Razlychnыe podkhodы k otsenke dynamycheskykh, эnerhetycheskykh y tekhnolohycheskykh vozmozhnostei vybratsyonnыkh mashyn . Vybratsyy v tekhnyke y tekhnolohyiakh. Vseukrainskyi naukovo-tekhnichnyi zhurnal. № 3 (35).113-117.
19. Kopыlov Yu.R.( 1998). Amplytudnыe y fazo-chastotnыe kharakterystyky vybryruiushchei rabochei sredы .Vybratsyy v tekhnyke y tekhnolohyiakh. Trudы III mezhdunarodnoi nauchno-tekhnycheskoi konferentsyy. Evpatoryia.133-137.
20. Chlenov V.A., Mykhailov N.V. (1972). Vybrokypiashchyi sloi. M.: Nauka. 341.
21. Blekhman Y.Y.( 1994) .Vybratsyonnaia mekhanyka. M: Fyzmatlyt. 400 .
About journal
The journal "Vibrations in engineering and technology" presents materials on the following issues
• Theory of processes and machines
• Mechanical Engineering and materialprocessing
• Processing and food production
The journal "Vibrations in Engineering and Technologies" is included in the list of technical scientific publications of Ukraine
(Category "B", Order of the Ministry of Education and Science of Ukraine dated July 2, 2020 No. 886)
Old version of the site: http://vibrojournal.vsau.edu.ua/
The journal "Vibrations in Engineering and Technology" is indexed by the following databases and catalogs:
The certificateof massmedia State registration:kv no 16643-5115 from 30.04.2010 .
Founder of the journal: Vinnytsia National Agrarian University
Kind of publication: journal
Type of publication : Scientific
Publication status: Domestic
Year of founding:
Periodicity: 4 times a year
Extent: 18.75 nominal printed pages
ISSN: 2306-8744 (printed version), (online)
Language of edition : (mixed languages) Ukrainian, English
The scope of the distribution and the category of readers: national, foreign, teaching staff, scientists, businessmen.
Periodical is included in the list of scientific professional editions of Ukraine approved by the Order of Ministry of Education and Sciences of Ukraine from 21.12.2015 No. 1328.
The journal "Vibrations in engineering and technology" is included in the "Catalogue of periodicals of Ukraine".
Journal subscription can be executed in each post office department.
Subscription Index is 99720.
Old version of site: http://vibrojournal.vsau.edu.ua/
In June 1994 the 2nd International Scientific and Technical Conference "Application of vibrations for technological purposes" was organized on the basis of Vinnytsia State Agricultural Institute. Leading experts in this field, noting the significant contribution to the school of Vibration Engineering under the leadership of P. S. Bernyk, proposed to create a professional all-Ukrainian scientific and technical journal "Vibration in engineering and technology..The journal was foundedat Vinnytsia State Agricultural Institute and P.S. Bernyk was elected to be the chief editor .
For all these years (since 1994) theJournal "vibration in engineering and technology" published 94 issues wherestudy of vibration effects, the creation of progressive energy saving technologies and equipment for their implementation were highlighted.
Currently Kaletnik H.M PhD , professor, academician NAAS is the chief editor of the "Vibrations in engineering and Technology"
The journal "Vibration in Engineering and technology", which has no analogues on the territory of Ukraine, is well known abroad.
